Analogue craft

What is a transparency? Slide film explained

An older man in a flat cap smokes beside water and open hills.
A man smoking in the Highlands.Photograph by Robert Harper. Robert Harper Photograph Library, Archive.London. From the archive, shown for illustration.

A transparency is the photograph itself, in positive, on the film that went through the camera. That simple fact explains how it was shot, why publishers wanted it and why it is demanding to scan.

A transparency is a positive photograph on clear film. Hold one up to a window and the picture is there in full colour, the right way round in tone, on the very piece of film that was in the camera when the shutter opened. There is no negative behind it and no print in front of it. For most of the later twentieth century that small rectangle of film was what a photographer delivered, what a picture editor chose and what a printer was told to match.

What is a transparency in photography?

The word describes how the picture is seen: by light passing through it. A print reflects light; a transparency transmits it. The film that produces one is called reversal film, and the same material goes by several names, which is the main source of confusion.

  • Reversal film is the technical term, after the reversal step in processing.
  • Transparency film and positive film describe the result.
  • Slide film comes from the 35mm habit of putting each frame in a mount for projection.
  • Chrome is trade shorthand, taken from brand names such as Kodachrome, Ektachrome and Fujichrome.
  • Diapositive, or dia, is the usual term in much of continental Europe.

Strictly, a slide is a mounted transparency. The standard mount for a 35mm frame is a 2 x 2 inch square of card or plastic. Roll-film and sheet-film transparencies were more often left unmounted and kept in sleeves or black card masks. The distinctions between these terms and the negative are set out in slides, transparencies and negatives: what is the difference?

How does slide film make a positive image?

All camera film first forms a negative. Reversal processing then turns it round. In outline, a first developer brings up a black-and-white negative image in each of the film's colour-sensitive layers. The film is then chemically fogged or re-exposed so that all the silver halide not used by that negative becomes developable. A colour developer works on this remainder and, as it does, forms cyan, magenta and yellow dyes in proportion. Bleach and fixer then remove all the silver, negative and positive alike, and what is left is a positive image made only of dye.

Today that sequence is the E-6 process, which superseded Kodak's earlier E-3 and E-4 processes. It is temperature-critical: Kodak's published figures hold the first developer at about 38°C (100°F). All colour reversal film currently sold is made for E-6.

Kodachrome was the great exception. Introduced as 16mm cine film in 1935 and as 35mm still film in 1936, it was among the first commercially successful subtractive colour films, and it carried no dye-forming couplers in its emulsion. The dyes were added during processing, layer by layer, in a procedure known in its final form as K-14, which needed specialised machinery. Kodak announced the end of Kodachrome manufacture on 22 June 2009. The last laboratory running the process, Dwayne's Photo in Parsons, Kansas, accepted its final rolls at the end of December 2010.

What sizes did transparencies come in?

Reversal film was made in every common film size, so a transparency can be little bigger than a postage stamp or as large as a sheet of writing paper.

Film Typical frame How it is usually found
35mm (135) 24 x 36 mm In 2 x 2 inch slide mounts, or uncut strips in sleeves
120 roll film, 6x4.5 about 56 x 41.5 mm Cut singly or in strips, in sleeves or card masks
120 roll film, 6x6 about 56 x 56 mm As above; sometimes in larger glassless mounts
120 roll film, 6x7 about 56 x 70 mm As above; ten frames to a roll
120 roll film, 6x9 about 56 x 84 mm As above; eight frames to a roll
Sheet film 4 x 5 inches and larger One image per sheet, in individual sleeves

The differences between the sizes are covered in film formats explained, and the larger roll-film frame gets its own treatment in the 6x7 format: why "the ideal format" filled studio archives.

Why did photographers and magazines use transparency film?

Because the transparency settled arguments. A colour negative has to be interpreted before anyone can judge it, and two printers will interpret it differently. A transparency shows what was captured, without printing. An editor could put a sheet of them on a lightbox with a magnifier and choose. The repro house then had a physical object to compare its proofs with. Until about 1995 colour transparency was the preferred original for publication, and slide film is generally credited with more saturated colour and finer grain than colour negative film of similar speed.

The price was discipline. Reversal film has fewer stops of exposure latitude than colour negative film, and there is no printing stage in which to rescue a mistake. What was exposed is what exists. That is one reason studio photographers tested lighting and exposure on instant film before committing to a roll, a practice described in Polaroids in the studio: proofing before digital.

How do you look at a transparency, and how do you scan one?

For viewing, the reference is a daylight-balanced lightbox. The US federal digitisation guidelines (FADGI, third edition, May 2023) specify a 5,000 K transmissive lightbox with a colour rendering index better than 90 for assessing transparencies. Handle film by its edges, or a slide by its mount, and keep viewing sessions short: dyes are sensitive to light as well as heat, a subject covered in why colour slides fade.

For scanning, a transparency has one advantage and one difficulty. The advantage is that the scan can be compared directly with the original, so there is a right answer. The difficulty is density: FADGI notes that transparency films can reach a maximum density near 4.0, which stretches the optics and sensors of most equipment. The same guidelines set preservation capture for film from 35mm to 4 x 5 inches at about 3,000 pixels per inch for three stars and about 4,000 for four, at 16 bits per channel. The film scan resolution calculator converts those figures into pixel dimensions and file sizes for each format, and the image histogram tool shows whether a scan has clipped the deep shadows that slide film is known for.

Transparencies in the Robert Harper archive

The Robert Harper Photograph Library is, in large part, a transparency archive. Its inventory records 52,684 unique analogue photographs, and gives 6 x 7 colour transparency film as the principal analogue format, alongside 35mm slides, black-and-white negatives, contact sheets and 4,005 Polaroid prints. The counts come from the archive's inventory and have not been checked frame by frame against the physical material. One folder of 842 transparencies has been scanned; more than half of the archive is still on film and has yet to be scanned. The inventory does not record film stocks, so nothing is claimed here about which emulsions are in the boxes.

The analogue collections describe what is held, and the folder-by-folder listing is in the archive inventory. Researchers, picture editors and publishers who would like to discuss material that has not yet been scanned can make a request through professional access.

Frequently asked questions

What is a transparency in photography?

A transparency is a positive photographic image on a transparent film base. It is made on reversal film, which is processed so that the film exposed in the camera becomes the finished picture, with light areas light and colours as they were. It is viewed by shining light through it, on a lightbox or with a projector, and is also called a slide or a chrome.

Is a slide the same as a transparency?

Nearly. A transparency is any positive image on film. A slide is a transparency put in a card, plastic or glass mount so that it can be projected; for 35mm film the standard mount is 2 x 2 inches. Larger transparencies were usually kept unmounted in sleeves or card masks. In everyday speech the two words are used interchangeably.

What is the difference between slide film and negative film?

Slide film gives a positive on the film itself, so no print is needed to see the picture. Negative film records tones in reverse, and colour negative film also carries an orange mask, so it has to be printed or inverted digitally. Slide film generally has less exposure latitude than colour negative film, which makes accurate exposure more important.

Can you still get transparency film developed?

Yes. All colour reversal film sold today is developed in the E-6 process, which specialist laboratories still run. Kodachrome is the exception: it needed its own K-14 process, Kodak announced the end of the film on 22 June 2009, and the last laboratory to process it stopped accepting rolls at the end of December 2010.

How should a transparency be digitised?

With a film scanner, a flatbed that has a transparency unit, or a digital camera over a light source. Published guidelines for preservation masters point to about 3,000 to 4,000 pixels per inch at 16 bits per channel, with the scan matched to the film as it is. Keep some film border and make corrections on a copy.

Sources

Published by Archive.London. Corrections are welcome under our editorial policy.

Help digitise the archive

52,684 analogue originals, mostly medium-format transparencies, are waiting to be scanned and catalogued. We are speaking to scanning, cataloguing and tagging partners.

See the digitisation briefWrite to the archive