Free image tools

Print size calculator: pixels to print size at any ppi

Find out how large an image will print at a given ppi, or how many pixels a print of a given size requires. Includes guidance on how viewing distance changes the resolution you need.

This tool needs JavaScript. It runs entirely in your browser; nothing is uploaded.

Private by design. Your files are processed by your own browser on your own device. They are not uploaded, stored or seen by Archive.London. Tool terms

How to use the Print Size and DPI Calculator tool

  1. Enter the pixel width and height of your image, or the print size you want.
  2. Set the ppi, for example 300 for a print viewed in the hand.
  3. Read the resulting print size or the pixel dimensions required.
  4. Check the viewing-distance guidance to see whether a lower ppi would do.

To calculate print size, open the Print Size and DPI Calculator on Archive.London and enter your image's pixel dimensions and a ppi value. It gives the print size, or works the other way from a print size to the pixels required. Viewing-distance guidance shows when a lower ppi is acceptable. Nothing is uploaded.

The formula, with examples

Print size in inches is pixels divided by ppi. Pixels required are inches multiplied by ppi. Everything else follows from that.

  • A 6000 × 4000 pixel image prints at 20 × 13.3 inches at 300 ppi, or 40 × 26.7 inches at 150 ppi.
  • An A4 page, 210 × 297 mm, needs about 2480 × 3508 pixels at 300 ppi.
  • A 10 × 8 inch print at 300 ppi needs 3000 × 2400 pixels.

Note that ppi, pixels per inch in the file, is not the same as a printer's dpi, the dots of ink it lays down. An inkjet may place well over a thousand dots per inch to render an image supplied at 300 ppi. When a lab or publisher asks for 300 dpi they almost always mean 300 pixels per inch at the final printed size.

Viewing distance: why posters need fewer pixels per inch

The 300 ppi convention assumes a print held at reading distance. The eye resolves less detail as distance increases, so larger prints viewed from further away can use a lower density without looking soft.

A common rule of thumb, based on normal visual acuity of about one arcminute, is that the ppi needed is roughly 3438 divided by the viewing distance in inches. At 12 inches that gives about 290 ppi, which is where the 300 figure comes from. At one metre it falls to under 90 ppi, and at two metres to under 45.

This is why a billboard can be printed from a modest file. It is also a caution: people walk up to exhibition prints. If viewers can approach closely, specify for the closest distance, not the average one.

When the pixels fall short

If the calculation shows you are short of pixels, there are sound options and poor ones.

Printing smaller, or accepting 200 to 240 ppi, usually gives a good result, particularly from a sharp original. Enlarging the file by interpolation produces the pixel count a specification demands but cannot create detail that was never recorded. The best remedy is a larger original: a higher-resolution scan from the film, or the camera's full-size file in place of a web copy.

Also allow for the aspect ratio. A 3:2 image does not fill a 10 × 8 inch sheet without cropping, so check the shorter dimension as well as the longer.

This page is a calculator only. No image is loaded and the figures you enter stay in your browser.

From transparency to printed page

For photographs that originate on film, print size is ultimately decided at the scanner. The enlargement a reproduction can stand depends on the size of the original and the resolution at which it was scanned, which is one reason magazine and advertising photographers favoured medium-format film: a larger original needs less magnification to fill a page.

Picture researchers planning a book or exhibition can use the calculator to state requirements precisely when requesting files, in pixels and at a named print size. Collections in the Robert Harper Photograph Library can be browsed by subject in the photography archive index.

Frequently asked questions

How many pixels do I need for an A4 print?

At 300 ppi, an A4 page of 210 × 297 mm needs about 2480 × 3508 pixels, which is around 8.7 megapixels. At 200 ppi it needs about 1654 × 2339 pixels. If the print has a white border, calculate for the image area only. Most current cameras and phones exceed these figures comfortably.

Is 300 dpi always necessary for printing?

No. It is a safe standard for material viewed at reading distance, such as books, magazines and small photographic prints. Larger prints seen from further back look sharp at lower densities, and many labs print well at 200 to 240 ppi. Ask your printer what they recommend for the specific process and paper, since requirements differ.

How big can I print a 12 megapixel photo?

A typical 12 megapixel image is 4000 × 3000 pixels. That prints at 13.3 × 10 inches at 300 ppi, 20 × 15 inches at 200 ppi and 26.7 × 20 inches at 150 ppi. The larger sizes suit prints that hang on a wall and are viewed from a step or two back.

What is the difference between ppi and dpi?

PPI is pixels per inch, a property of how an image file is scaled for print. DPI is dots per inch, strictly a measure of how many ink dots a printer places. In everyday use the terms are mixed, and a request for a 300 dpi image means 300 pixels per inch at the printed size. Printers use many ink dots to reproduce each pixel.

How do I convert pixels to centimetres for printing?

Divide the pixel dimension by the ppi to get inches, then multiply by 2.54, since one inch is exactly 2.54 cm. A 3000 pixel edge at 300 ppi is 10 inches, or 25.4 cm. Put another way, 300 ppi is about 118 pixels per centimetre. Density is quoted per inch because printers, publishers and image software use that unit.

Help digitise the archive

52,684 analogue originals, mostly medium-format transparencies, are waiting to be scanned and catalogued. We are speaking to scanning, cataloguing and tagging partners.

See the digitisation briefWrite to the archive