Digitising film archives

Camera scanning film: a practical set-up guide

Two workers handle a ladle beside industrial machinery in a black-and-white workshop photograph.
Lead pipe making, Paisley, 1975.Photograph by Robert Harper. Robert Harper Photograph Library, Archive.London. From the archive, shown for illustration.

Photographing film with a digital camera is the fastest way to digitise it and the easiest to get subtly wrong. Five components and one alignment check decide the result.

Camera scanning means photographing a piece of film, lit from behind, with a digital camera and a macro lens. One exposure of a fraction of a second replaces a scanner pass that can take minutes, which is why the method is now widely used for large collections. It also moves responsibility for quality from the manufacturer of a sealed box to whoever assembles the rig. This guide covers the components, the alignment, the resolution that each film format really receives, and the checks that keep a fast method from becoming a careless one.

What equipment does camera scanning need?

Five things, each with one job.

A camera that records raw files. Sensor resolution sets the ceiling on detail. Raw capture preserves the full bit depth of the sensor and postpones decisions about tone and colour. An electronic or electronic-first-curtain shutter avoids vibration from the mechanism.

A flat-field macro lens. This is the component most often underestimated. The US federal digitisation guidelines (FADGI, third edition, May 2023) say that general-purpose lenses are unsuitable for close-focus film scanning and that flat-field, apochromatic designs are needed; elsewhere they note that lens quality can limit the resolution of the whole system. A lens that is sharp in the centre and soft at the corners will give every frame in an archive the same defect.

A rigid support. A copy stand, or a horizontal rail, holding camera and film in fixed relation. FADGI warns that the effects of vibration become much more noticeable at high magnification, which describes film capture exactly.

An even, high-quality light source. A diffused, flicker-free, daylight-balanced panel with a high colour rendering index. FADGI specifies a 5,000 K lightbox with a colour rendering index better than 90 for viewing transparencies, and the same standard is a sound minimum for photographing them. Uneven light becomes uneven density in every file.

A film holder with a mask. It has to do three things: keep the film flat, block all light except what passes through the frame, and allow film to be advanced without touching the image. Stray light from around the film flares in the lens and lowers contrast.

A sixth item costs nothing: a dark room. FADGI advises working in a dimly lit space so that ambient light does not affect the capture. Room light reflecting off the top surface of the film is a common cause of flat, hazy results.

How do you align the camera with the film?

If the sensor and the film are not parallel, one side of the frame will be out of focus, and at macro distances the tolerance is small.

  1. Fix the camera to the stand, lens pointing at the light source.
  2. Lay a small mirror on the film stage, exactly where the film will sit.
  3. Look through the viewfinder or live view. You will see the reflection of the lens.
  4. Adjust the camera, or level the stage, until the reflected lens is centred in the frame.
  5. Lock every adjustment, remove the mirror, and focus on the film grain at full magnification.

Recheck alignment whenever the rig is moved, the column height is changed for a different film format, or results begin to look soft on one edge.

How much resolution does camera scanning give for each format?

The arithmetic is simple and often surprising. Sampling resolution is the number of sensor pixels across the film, divided by the film's width in inches. With a 3:2 sensor, 35mm film fills the frame exactly. Roll-film formats are squarer, so their short side has to fit across the sensor's short side and the rest of the sensor is wasted.

Sensor (pixels) 35mm frame, 24 x 36 mm 6x6 or 6x7 frame, 56 mm short side
6,000 x 4,000 (24 MP) about 4,200 ppi about 1,800 ppi
8,256 x 5,504 (45 MP) about 5,800 ppi about 2,500 ppi
9,504 x 6,336 (60 MP) about 6,700 ppi about 2,900 ppi

These are single-exposure figures with the frame filling the sensor. For comparison, FADGI's three- and four-star levels for film from 35mm to 4 x 5 inches are about 3,000 and 4,000 ppi. A 24-megapixel camera clears the four-star figure on 35mm. No single exposure in the table does so on medium format. The megapixel calculator and the film scan resolution calculator will run the sums for other sensors and formats.

Two qualifications. First, FADGI points out that sensors with a colour filter array do not record full colour at every pixel; the missing values are interpolated, so true resolution is lower than the stated pixel count. Pixel-shift modes, which move the sensor between several exposures to sample each point in every colour, reduce that loss on a static subject such as film. Second, more resolution is available by tiling. FADGI accepts that large transparencies may need tiled capture and stitching, and treats the stitched file as the production master. Four overlapping shots of a 6x7 frame come close to doubling the sampling on each axis, at the cost of time and the risk of stitching errors.

What a 6x7 frame demands at each level is laid out in the 6x7 format.

What camera settings work best?

  • Raw, lowest native ISO. Noise in a scan looks like extra grain.
  • A middle aperture found by test. Wide open, corners soften; stopped far down, diffraction blurs everything. Photograph a sharp piece of film at each aperture and compare corners.
  • Manual exposure, fixed for the batch where possible. For transparencies, expose so that the clear film edge is just short of clipping. For negatives, FADGI's advice is to treat the film as a transparency and make sure neither end is clipped. The image histogram tool gives a second opinion on a test frame.
  • Fixed white balance, set on the bare light source, so that every frame is recorded on the same basis.
  • Remote release or a short delay, so that nothing touches the camera during exposure.
  • Consistent orientation. Many operators place the emulsion side towards the lens, so that the lens is not looking through the film base, and mirror the image afterwards. Whichever way you choose, apply it to the whole project and write it down.

What happens to the files after capture?

A raw file is not yet an archival master. The usual sequence is to convert raw captures to 16-bit TIFF or DNG with no creative adjustments, embed a colour profile, and keep that as the master, as discussed in TIFF, DNG or JPEG 2000: choosing a preservation format.

Negatives then need inversion on a copy. FADGI recommends software that uses scene-balancing methods for colour negatives, since the orange mask and the film's response differ from stock to stock. For quick viewing copies, the film negative to positive converter removes the mask from a sample of the film rebate and inverts in the browser. How to scan black-and-white negatives covers silver film.

Transparencies can be profiled, as with a scanner, by photographing an IT8 target under the same light. Colour management for film scanning explains what that does and does not fix.

Dust is the method's weak point. A camera has no infrared channel, so there is no automatic defect map. Film has to be blown clean before each exposure, and what remains is retouched on a production copy.

How do you keep quality consistent across thousands of frames?

By measuring. FADGI's position is that the whole imaging system should be tested, and that capture quality for film should be monitored with standard film targets and analysis software. In a working routine that means photographing a resolution and density target at the start of each session, rechecking alignment and focus at intervals, and inspecting a sample of every batch at full magnification before the film goes back in its box.

Throughput deserves the same honesty. Exposure takes a moment; handling does not. Loading, dusting, framing, checking and re-sleeving set the real rate. Put a realistic figure for seconds per frame into the digitisation time and cost calculator and the size of a project becomes clear. How the method compares with flatbed and drum scanning is covered in scanner, drum or camera: three ways to capture film.

Camera scanning and the Robert Harper archive

The Robert Harper Photograph Library's inventory records 134,340 analogue frames, counting duplicates and variants, with 6 x 7 colour transparency film as the principal format. The figures come from the inventory and have not been checked frame by frame against the physical material. One folder of 842 transparencies has been scanned, and more than half of the archive is still on film and has yet to be scanned. No capture method has been announced for the rest. For film of this size and quantity, the trade-off described above, between single-shot speed and four-star resolution, is the central question a scanning partner will be asked.

The holdings are described in the analogue collections and itemised in the archive inventory. Studios and vendors with camera-based film capture systems are invited to make contact through the digitisation partners page.

Frequently asked questions

Is camera scanning as good as a film scanner?

It can be, with the right lens and careful alignment. A high-resolution camera with a flat-field macro lens can match or exceed desktop scanners for detail and is far quicker. Its disadvantages are the lack of infrared dust removal, the need to invert and colour-correct negatives yourself, and the fact that quality depends on your set-up, not on a sealed machine.

What lens do I need for camera scanning film?

A true macro lens that reaches the magnification your film format needs, sharp to the corners with a flat field. FADGI's guidelines state that general-purpose lenses are unsuitable for close-focus film capture and recommend flat-field apochromatic designs. For 35mm film on a full-frame sensor that means 1:1 magnification; larger film needs less magnification for a single shot.

What light source should I use for camera scanning?

An even, flicker-free, daylight-balanced panel with a high colour rendering index, diffused so that no texture or hot spot shows through the film. For assessing transparencies, FADGI specifies a 5,000 K transmissive lightbox with a colour rendering index above 90, which is a sensible benchmark for capture as well. Mask off all light around the frame.

How many megapixels do I need to camera scan film?

Enough to reach your target sampling on the film's short side. A 24-megapixel sensor gives about 4,200 ppi on 35mm, which meets FADGI's four-star figure on paper. The same sensor gives only about 1,800 ppi on a 6x7 frame, so medium format needs a higher-resolution camera, pixel-shift capture, or several overlapping shots stitched together.

How do I get the camera parallel to the film?

Use a mirror. Lay a small mirror flat where the film sits, look through the camera, and adjust until the reflection of the lens is exactly centred in the frame. When it is, the sensor is parallel to the film plane. Lock everything, remove the mirror, and recheck whenever the rig is moved or the column height changes.

Sources

Published by Archive.London. Corrections are welcome under our editorial policy.

Help digitise the archive

52,684 analogue originals, mostly medium-format transparencies, are waiting to be scanned and catalogued. We are speaking to scanning, cataloguing and tagging partners.

See the digitisation briefWrite to the archive