Free image tools

ND filter calculator for long exposure times

Enter the shutter speed you metered without the filter and the strength of the filter, in stops or as an ND factor such as ND8, ND64 or ND1000, to get the exposure time with the filter fitted.

This tool needs JavaScript. It runs entirely in your browser; nothing is uploaded.

Private by design. Your files are processed by your own browser on your own device. They are not uploaded, stored or seen by Archive.London. Tool terms

How to use the ND Filter Exposure Calculator tool

  1. Meter the scene without the filter and note the shutter speed.
  2. Enter that base shutter speed.
  3. Enter the filter strength in stops, or as an ND factor such as ND8, ND64 or ND1000.
  4. Read the new exposure time and set it on the camera, using bulb mode and a timer for long times.

To calculate a long exposure with an ND filter, open the Archive.London ND filter calculator, enter the shutter speed metered without the filter and the filter strength in stops or as an ND factor. Each stop doubles the time, so a 10-stop filter turns 1/60 second into about 17 seconds. Treat the result as an estimate.

Stops, ND factors and the doubling rule

A neutral density filter cuts light evenly across the visible spectrum. Each stop of density halves the light, so the exposure time doubles for every stop: new time = base time × 2^stops. The ND factor is that multiplier written out.

  • ND8: 3 stops, 8 times the exposure
  • ND64: 6 stops, 64 times
  • ND1000: 10 stops, about 1,000 times (the exact figure is 1,024)

So 1/125 second becomes about half a second with a 6-stop filter, and 1/60 becomes about 17 seconds with a 10-stop filter. A base exposure of 1/4 second with 10 stops runs to more than four minutes. Filters marked by optical density follow the same scale at 0.3 per stop: ND 0.9 is 3 stops and ND 3.0 is 10. Stacked filters add their stops together, which multiplies their factors.

Why the calculated time is a starting point

The arithmetic is exact; filters are not. A filter sold as 10 stops may measure a third of a stop or more either side, and strong filters often add a colour cast that shifts the result further. Light also changes during a long exposure, particularly around dawn and dusk, and stray light entering an SLR viewfinder can fog a frame unless the eyepiece is covered.

On digital cameras, make a test frame, check the histogram and adjust. On film there is a further correction that this calculator does not apply: reciprocity failure. Most films lose effective sensitivity once exposures pass about a second, and need extra time on top of the calculated figure. The amount differs widely between emulsions, so use the film maker's data sheet for the stock you are shooting.

From the archive: time as a creative control

Neutral density filters exist to buy time or aperture: to smooth moving water and cloud in a landscape, to blur crowds out of a street, or to keep a wide aperture in bright light. The choice of shutter time has always been one of the main decisions in landscape and marine photography, on film as much as on digital.

The photography archive index covers both subjects, with collections of Scottish and other landscapes and a later body of sailing and superyacht work, as well as places from Iceland to the Côte d'Azur. It is a useful reference for how water, weather and light have been handled across several decades of professional practice.

Frequently asked questions

How many stops is an ND1000 filter?

Ten stops. Ten doublings give a factor of 1,024, which makers round to ND1000. A 10-stop filter turns 1/30 second into about 34 seconds and 1 second into about 17 minutes. It is the usual choice for daytime long exposures of water and moving cloud.

How do I convert ND factor to stops?

Take the base 2 logarithm of the factor, or count the doublings from 1. ND2 is 1 stop, ND4 is 2, ND8 is 3, ND16 is 4, ND32 is 5, ND64 is 6. Going the other way, raise 2 to the power of the number of stops. The calculator accepts either form.

What happens if I stack two ND filters?

Their stops add and their factors multiply. A 3-stop ND8 on a 6-stop ND64 gives 9 stops, a factor of 512. Enter the combined stops in the calculator. Stacking can cause vignetting on wide lenses and increases any colour cast, so check a test frame.

Do I need to adjust for reciprocity failure on film?

Usually yes, for exposures longer than about a second. Film becomes less responsive at very low light intensities, so the calculated time underexposes. The correction varies by emulsion and can be substantial at exposures of a minute or more. This calculator gives the uncorrected time; add the correction from the film's data sheet.

Should I meter before or after fitting the filter?

Meter and focus before fitting a strong filter, then enter that reading as the base shutter speed. Through a 10-stop filter many cameras cannot meter or autofocus reliably. Keep the aperture and ISO unchanged, switch to manual or bulb mode, fit the filter and use the calculated time.

Help digitise the archive

52,684 analogue originals, mostly medium-format transparencies, are waiting to be scanned and catalogued. We are speaking to scanning, cataloguing and tagging partners.

See the digitisation briefWrite to the archive